ref: debb01e5c38437116a5e491710257fd6f2e1d0e7
dir: /testbin/welsenc.cfg/
# Cisco Scalable H.264/AVC Extension Encoder Configuration File #============================== GENERAL ============================== UsageType 0 # 0: camera video 1:screen content SimulcastAVC 0 # 0: use SVC syntax for higher layers; 1: use Simulcast AVC SourceWidth 320 # input video width SourceHeight 192 # input video height InputFile ../res/CiscoVT2people_320x192_12fps.yuv # Input file OutputFile test.264 # Bitstream file MaxFrameRate 30 # Maximum frame rate [Hz] FramesToBeEncoded -1 # Number of frames (at input frame rate) TemporalLayerNum 2 # temporal layer number(1--4) IntraPeriod 0 # Intra Period ( multipler of GoP size or -1) SpsPpsIDStrategy 1 # sps/pps id strategy(0-4): # 0: const id, 1: increasing id, 2: sps list, # 3: sps list & pps increase, 4: sps/pps list EnableFrameCropping 1 # enable frame cropping flag EntropyCodingModeFlag 0 # 0:cavlc 1:cabac MaxNalSize 0 # Unit:Byte, Maximum Nal size ComplexityMode 0 # 0:low complexity mode 1:medium complexity mode # 2:high complexity mode #============================== LOOP FILTER ============================== LoopFilterDisableIDC 0 # Loop filter idc (0: on, 1: off, # 2: on except for slice boundaries, # 3: two stage. slice boundries on in second stage # 4: Luma on but Chroma off (w.r.t. idc=0) # 5: Luma on except on slice boundaries, but Chroma off in enh. layer (w.r.t. idc=2) # 6: Luma on in two stage. slice boundries on in second stage, but Chroma off (w.r.t. idc=3) LoopFilterAlphaC0Offset 0 # AlphaOffset(-6..+6): valid range LoopFilterBetaOffset 0 # BetaOffset (-6..+6): valid range #============================== SOFTWARE IMPLEMENTATION ============================== MultipleThreadIdc 1 # 0: auto(dynamic imp. internal encoder), # 1: multiple threads imp. disabled, # >1: count number of threads UseLoadBalancing 1 # under particular slice mode, when multi-threading is used, whether apply dynamic slicing for load balancing #============================== RATE CONTROL ============================== RCMode 0 # -1: rc off mode, 0: quality mode, 1: bitrate mode, # 2: buffer based mode,can't control bitrate, # 3: bitrate mode based on timestamp input TargetBitrate 5000 # Unit: kbps, controled by EnableRC also MaxOverallBitrate 0 # Unit: kbps, max bitrate overall, 0 - unspecified EnableFrameSkip 1 # Enable Frame Skip MaxQp 51 # maximum quant MinQp 0 # minimum quant #============================== DENOISE CONTROL ============================== EnableDenoise 0 # Enable Denoise (1: enable, 0: disable) #============================== SCENE CHANGE DETECTION CONTROL ======================= EnableSceneChangeDetection 1 # Enable Scene Change Detection (1: enable, 0: disable) #============================== BACKGROUND DETECTION CONTROL ============================== EnableBackgroundDetection 1 # BGD control(1: enable, 0: disable) #============================== ADAPTIVE QUANTIZATION CONTROL ======================= EnableAdaptiveQuantization 1 # Enable Adaptive Quantization (1: enable, 0: disable) #============================== LONG TERM REFERENCE CONTROL ============================== EnableLongTermReference 1 # Enable Long Term Reference (1: enable, 0: disable) LtrMarkPeriod 30 # Long Term Reference Marking Period #============================== LAYER DEFINITION ============================== PrefixNALAddingCtrl 0 # Control flag of adding prefix unit (0: off, 1: on) # It shall always be on in SVC contexts (i.e. when there are CGS/MGS/spatial enhancement layers) # Can be disabled when no inter spatial layer prediction in case of its value as 0 NumLayers 1 # Number of layers //LayerCfg layer0.cfg # Layer 0 configuration file //LayerCfg layer1.cfg # Layer 1 configuration file LayerCfg layer2.cfg # Layer 2 configuration file