ref: 0e73d218bc9c87aebd60b64d772c8b9ece883a68
dir: /docs/DEBUG/
Debugging within the FreeType sources
=====================================
I. Configuration macros
-----------------------
There are several ways to enable debugging features in a FreeType 2
builds. This is controlled through the definition of special macros
located in the file `ftoptions.h'. The macros are:
FT_DEBUG_LEVEL_ERROR
#define this macro if you want to compile the FT_ERROR macro calls
to print error messages during program execution. This will not
stop the program. Very useful to spot invalid fonts during
development and to code workarounds for them.
FT_DEBUG_LEVEL_TRACE
#define this macro if you want to compile both macros FT_ERROR and
FT_TRACE. This also includes the variants FT_TRACE0, FT_TRACE1,
FT_TRACE2, ..., FT_TRACE7.
The trace macros are used to send debugging messages when an
appropriate `debug level' is configured at runtime through the
FT2_DEBUG environment variable (more on this later).
FT_DEBUG_MEMORY
If this macro is #defined, the FreeType engine is linked with a
small but effective debugging memory manager that tracks all
allocations and frees that are performed within the font engine.
When the FT2_DEBUG_MEMORY environment variable is defined at
runtime, a call to FT_Done_FreeType will dump memory statistics,
including the list of leaked memory blocks with the source
locations where these were allocated. It is always a very good
idea to define this in development builds. This works with _any_
program linked to FreeType, but requires a big deal of memory (the
debugging memory manager never frees the blocks to the heap in
order to detect double frees).
When FT2_DEBUG_MEMORY isn't defined at runtime, the debugging
memory manager is ignored, and performance is unaffected.
II. Debugging macros
--------------------
Several macros can be used within the FreeType sources to help
debugging its code:
1. FT_ERROR(( ... ))
This macro is used to send debug messages that indicate relatively
serious errors (like broken font files), but will not stop the
execution of the running program. Its code is compiled only when
either FT_DEBUG_LEVEL_ERROR or FT_DEBUG_LEVEL_TRACE are defined in
`ftoption.h'.
Note that you have to use a printf-like signature, but with double
parentheses, like in
FT_ERROR(( "your %s is not %s\n", "foo", "bar" ));
2. FT_ASSERT( condition )
This macro is used to check strong assertions at runtime. If its
condition isn't TRUE, the program will abort with a panic message.
Its code is compiled when either FT_DEBUG_LEVEL_ERROR or
FT_DEBUG_LEVEL_TRACE are defined. You don't need double
parentheses here. For example
FT_ASSERT( ptr != NULL );
3. FT_TRACE( level, (message...) )
The FT_TRACE macro is used to send general-purpose debugging
messages during program execution. This macro uses an *implicit*
macro named FT_COMPONENT used to name the current FreeType
component being run.
The developer should always define FT_COMPONENT as appropriate,
for example as in
#undef FT_COMPONENT
#define FT_COMPONENT trace_io
The value of the FT_COMPONENT macro is an enumeration named
`trace_XXXX' where `XXXX' is one of the component names defined in
the internal file `internal/fttrace.h'. If you modify FreeType
source and insert new `trace_XXXX' macro, you must register it in
`fttrace.h'. If you insert or remove many trace macros, you can
check the undefined or the unused trace macro by
`src/tools/chktrcmp.py'.
Each such component is assigned a `debug level', ranging from 0 to
7, through the use of the FT2_DEBUG environment variable
(described below) when a program linked with FreeType starts.
When FT_TRACE is called, its level is compared to the one of the
corresponding component. Messages with trace levels *higher* than
the corresponding component level are filtered and never printed.
This means that trace messages with level 0 are always printed,
those with level 2 are only printed when the component level is
*at least* 2.
The second parameter to FT_TRACE must contain parentheses and
correspond to a printf-like call, as in
FT_TRACE( 2, ( "your %s is not %s\n", "foo", "bar" ) )
The shortcut macros FT_TRACE0, FT_TRACE1, FT_TRACE2, ...,
FT_TRACE7 can be used with constant level indices, and are much
cleaner to use, as in
FT_TRACE2(( "your %s is not %s\n", "foo", "bar" ));
III. Environment variables
--------------------------
The following environment variables control debugging output and
behaviour of FreeType at runtime.
FT2_DEBUG
This variable is only used when FreeType is built with
FT_DEBUG_LEVEL_TRACE defined. It contains a list of component
level definitions, following this format:
component1:level1 component2:level2 component3:level3 ...
where `componentX' is the name of a tracing component, as defined
in `fttrace.h', but without the `trace_' prefix. `levelX' is the
corresponding level to use at runtime.
`any' is a special component name that will be interpreted as
`any/all components'. For example, the following definitions
set FT2_DEBUG=any:2 memory:5 io:4 (on Windows)
export FT2_DEBUG="any:2 memory:5 io:4" (on Linux with bash)
both stipulate that all components should have level 2, except for
the memory and io components which will be set to trace levels 5
and 4, respectively.
FT2_DEBUG_MEMORY
This environment variable, when defined, tells FreeType to use a
debugging memory manager that will track leaking memory blocks as
well as other common errors like double frees. It is also capable
of reporting _where_ the leaking blocks were allocated, which
considerably saves time when debugging new additions to the
library.
This code is only compiled when FreeType is built with the
FT_DEBUG_MEMORY macro #defined in `ftoption.h' though, it will be
ignored in other builds.
FT2_ALLOC_TOTAL_MAX
This variable is ignored if FT2_DEBUG_MEMORY is not defined. It
allows you to specify a maximum heap size for all memory
allocations performed by FreeType. This is very useful to test
the robustness of the font engine and programs that use it in
tight memory conditions.
If it is undefined, or if its value is not strictly positive, then
no allocation bounds are checked at runtime.
FT2_ALLOC_COUNT_MAX
This variable is ignored if FT2_DEBUG_MEMORY is not defined. It
allows you to specify a maximum number of memory allocations
performed by FreeType before returning the error
FT_Err_Out_Of_Memory. This is useful for debugging and testing
the engine's robustness.
If it is undefined, or if its value is not strictly positive, then
no allocation bounds are checked at runtime.
------------------------------------------------------------------------
Copyright 2002-2005, 2009, 2013 by
David Turner, Robert Wilhelm, and Werner Lemberg.
This file is part of the FreeType project, and may only be used,
modified, and distributed under the terms of the FreeType project
license, LICENSE.TXT. By continuing to use, modify, or distribute this
file you indicate that you have read the license and understand and
accept it fully.
--- end of DEBUG ---